The exhaust system will most likely consist of conversion-specific headers. You can find conversion headers at Summit Racing and many of the other companies listed in the source guide. Depending on your headers or exhaust manifolds, the steering might have to be moved over, or run through the header. The exhaust will have to be redone as well. The exhaust system will vary greatly, depending on what model and year the truck and engine are, and what state you live in for applicable smog laws.

The choice of header is going to make a difference on clearance, especially when it comes to the steering, the firewall, the oil pan, and the frame. Choose wisely for your particular application.

On some trucks (generation I and II S-10/S-15), the stock driveshaft will slide into the new automatic or manual transmission. The TH400/350, 700R4, and 4L60E transmissions all use the same spline for the transmission yoke. Depending on where the new motor is mounted, you will need to have the driveshaft lengthened or shortened, corresponding to the amount you move the engine forward or rearward. We always recommend that you have a heavy-duty driveshaft built to keep it from twisting. If you place the engine in the exact same spot as the original engine mounts, the driveshaft will be the same length. The stock rearend might be all right for your conversion, depending on the engine and transmission used and the size of the stock rearend. If you're going high performance, or your truck's stock differential is smaller than 8 inches, definitely look into using a larger differential. For the rearend, we recommend doing the same as with the driveshaft: Beef it up now while the swap is in progress (Ford 9-inch rearends seem to be the differentials and housings of choice).

We recommend using a stronger rearend and driveshaft to withstand the new performance output of your engine and transmission.

Most of the V-8 swaps performed aren't going to use the stock radiator; you'll need to upgrade to a radiator that has more cooling capacity. For example, the Corvette aluminum radiator that JTR offers is a very popular radiator for the S-10 350ci swaps. Your core support may need some modifications to make the new radiator fit. You'll also want to move the radiator as close to the front of the truck as possible without interfering with the grille and headlights. There are two options for cooling fans. If you have enough room for an engine-driven fan, you might want to consider using one. Otherwise, install at least one low-profile electric fan; if you can fit them, two are highly recommended. The area between the radiator and fan is where the engine seems to fit the tightest, so most people prefer to move their engine rearward. The running temperature of the engine is one of the major concerns of performing an engine swap, so this step is crucial.

A critical component of the engine swap is the proper-size radiator and cooling fans to keep your mini running without overheating.

The question about which fuel system you'll run depends primarily on your smog concerns and the applicable laws in your state. If you're planning on having a smog-legal truck after the swap, keep all the specified smog equipment that originally came with your donor motor (also available from the junkyard). The engine will also be fuel-injected, which in turn means you'll need a computer to manage the fuel system and other engine essentials. You can contact Howell Engine Developments, where you'll find the necessary components for fuel injection and wiring applications for most V-8 engines. If you're fortunate enough to live in a state where these laws don't apply, then carburetion is probably easier and less expensive, and can easily be tuned for high-performance applications.

For the electrical wiring of the new engine, you can attempt to piece together a wiring harness to work with the V-8 motor, or go with an aftermarket one. Depending on whether your engine for the swap is carbureted or fuel-injected, you may or may not need an engine management computer. It's easier and much cleaner to purchase a new harness from Painless Performance Wiring or Lee's High Tech Trucks. Both of these companies offer complete conversion harnesses as well as wiring tips and instructions. Having a complete harness made is especially nice since you can have your harness built to length.

Rewiring your truck with the new motor is made much cleaner with a complete wiring harness and instructions.

If you have air conditioning or power steering (especially on S-10s) and the truck isn't body-dropped, you might be able to keep your A/C and power steering by building or finding brackets that move the compressor and pump out of the way. A custom belt will have to be purchased in order to turn the compressor and pump. If your truck is body-dropped, or you have enormous rims (or both), check out Vintage Air's compact air-conditioning units. If your truck is or will be body-dropped, hood clearance could be another potential problem. With the bigger motor, consider using a cowl-induction hood for clearance. We recommend checking out some of the hoods Godfather Customs offers.

With this introduction to V-8 conversions complete, our next step will be the buildup of a 350ci crate motor. Check back next month to witness its construction in Volume II of our V-8 series. (Don't worry - in Volume III we'll actually swap the engine into an S-10.)